driven roller造句
例句与造句
- Nonlinear mechanical analysis of belt on driving roller
驱动部输送带的非线性力学分析 - 2 roller : driving roller , direction - chage roller and surface - add roller
2滚简：分传动滚简改向滚简和增面滚筒。 - Diameter of punched driving roller is large , suiting rewinding of large and small roll
复卷驱动辊直径大，适应大小卷径的复卷。 - The drive motor that turns the rubberised drive roller is a high performance stepping motor
转动胶制走纸滚筒的驱动电机是高性能的步进电机。 - The platform is divided into three driving segments , adopting three speed - stepless motors to drive roller via wheel gear
调速输坯台分3段传动，采用3台无级变速电机通过齿轮带动辊棒。 - It's difficult to find driven roller in a sentence. 用driven roller造句挺难的
- This shall erect bell cleanup scrapper in front of belt - drive roller , so that this clean up crude coal adhered onto belt
皮带驱动辊筒前安装有皮带清洁刮板，清除粘结于皮带上的原煤。 - S97 permanent magnet pulley can be selected as driving roller of this machine so that magnetic separation treatment can be carried out at the same time
该机的传动滚简可以选用s97系列永磁皮带轮，以便同时进行磁选处理。 - 5 sweeper : caput sweeper is installed at lower part of driving roller , while vacant section sweeper is installed at the end , near the direction - chage roller
5清扫器：头部清扫器安装在传动滚筒下方，空段清扫器安在尾部改向滚筒附近 - One end of belt - driven roller is fixed with machine body . the other end links with bolt - mode coupler at axial end of reducer . so that belt is easier replaced
皮带驱动辊筒一端固定于机体上，一端与减速机轴端插销式联轴器相连，使皮带更换更容易。 - Feeding and face fixing part : vfc motor , reduction drive , initiative , passivity drive roller . belt roller , face fixing , trimming and special width tape
输送整形部分：由变频控制电机、减速机、主、被动传动辊、调带辊、整形、修边及特种宽面胶带组成。 - When the swing arm axis made in the installation and wavering on the previous drive rollers above , this machinery can be directed to move forward for the movement and transport equipment
当摇摆臂安装在出力轴上和在摇摆传动器前面的滚子上面时，此机械可被引导一直向前运动并用作运输备。 - The driving rollers are electroplated with hard cr , tension self - controlling of winding - rollers are applied to the driving unit . the barrel of extruder , bullhead tee and die adopt cast aluminum heater which is endurable
挤出机料筒三通和模头均采用铸铝加热，牵引辊筒电镀硬铬，轮链轮采用 - 1 driving part : this machine adopts triangle beltdouble - grade drive for shaft speed reducer , speed reducer is installed on shaft head of driving roller ; all driving devices are installed on the machine frame viahead sheave rack and motor rack
1驱动部分：该机采用三角皮带轴装式减速器两级传动，减速器套装在传动滚筒的轴头上全部传动装置通过头轮架和电机架悬挂安装在机架上。 - The driving rollers ’ design is always the problem for belt conveyor factory and its design has been researched home and abroad for a long time . but the traditional design methods have many disadvantages . in the paper the driving rollers and the other key parts are analyzed with finite element parametric analysis method which is recently applied broadly
传动滚筒的设计一直是输送机生产厂家的一个难点,本文在分析了国内外研究和应用现状的基础上,总结了传统设计方法的不足,并应用目前广为使用的有限元方法对传动滚筒及其它关键部件进行了参数化分析。 - Supporting roller 12 : it can be dismantled to be repaired if the surface of roller is abraded , or channel of rollers is abraded unequally , or there is sunken hole , make sure that the two roller channels should have same diameter and be coaxial , outer diameter of the pair supporting rollers of every driving roller should be similar
辊面磨损或辊道不均匀磨损或产生凹坑时可拆下精车修理，但注意辊体的二个辊道直径一致并同轴，每个传动辊的一对托辊外径保持一致。